How to Build a Halfpipe or Ramp
Decide how tall you want your half-pipe to be and how wide the platform should be.You should have a minimum of 4' wide for the decks. You would need to make a full size template of the quarter-pipe so that you can use it to mark all of your end supports the same size. 1/4" plywood works very well for this.
- You can hold the pieces together with duct tape, but it's better to cut scab plates out of 3/4" ply where the seams join together and use 3/4" wood screws to hold the pieces together.
- Rip one sheet of ply in half the long way, well actually rip it to 23 and 3/4" so you can get two rips from one sheet.
- Cut two feet off of one of the rips and scab it to the full length piece. That should give you a 2 feet (0.6 m) by 10 feet (3.0 m) rectangle.
- Now scab together a 5 foot (1.5 m) square and hook it to the rectangle so that it looks like a giant boot.
- Drive a nail in the top corner of the 5 by 5 square that is not connected to the rectangle.
- Using that nail as a pivot, mark the radius from the top corner (where the 5x5 meets the rectangle) to the bottom corner directly below the nail.
- Cut this radius out using a jigsaw.(**Caution--use the plywood method for drawing the radius only if you have material to waste. Tip: put a nail or screw at the bottom of your radius, extend your tape measure to the desired length of your radius, use you tape measure as a pencil guide when drawing your radius**)
Use your template to make two end panels per quarter-pipe.To make the end panels, use two layers of inch (1.9 cm) plywood which you will laminate together. To laminate the layers, pour wood glue into a paint tray and use a roller to roll a thin even layer of glue over the entire surface of the bottom layer of ply. Lay the top layer down over the glue, turning the grain 90 degrees. Line up the edges. Screw the two layers together with 1 1/4" coarse thread wood screws. When the glue is set (overnight) use your template to mark out the end panels. Cut them out with a circular saw and or a jigsaw.
Use your template to make intermediate supports.These can be single layer 3/4" ply, scabbed together using 2 by material. Keep scab plates about two inches in from the edges.
Cut several 2x4s into 3 feet (0.9 m) 9in lengths.Use a stop block setup to make sure that they are all cut to identical lengths.
Line the flat edge of the 2x4s up with the edge of the end panels (where the riding surface will be) and screw or nail them to end panels a few inches apart.Nail the other end to the intermediate panel using the same spacing. Stagger the 2x4s between intermediate panels (so that you can nail/screw them). Use as many intermediate panels as necessary to get the overall length you want, and then use the other end panel at the opposite end. You will have to taper the bottom 2x4 to a profile that will fit to the ground.
You will have to frame under the platform to support not only your weight, but also hard landings.Now you need to get this framing anchored to the ground so that it won't tip over. Depending on your situation, you can anchor the back side of the platform to a building, or support beams poured with footings. Consult a professional on how to do this. Sandwich the intermediates with framing and run a carriage bolt through.
Once the framing is secure, you have to install the riding surface. inch (1.0 cm) CDX plywood should be flexible enough. You will have to run two layers, in the same direction. Break the seams by running a full course across the length, then run a 2 foot (0.6 m) rip with the grain running the same way on top. Be sure to stagger the end joints as well for added strength. Screw it to the 2x4s.
QuestionWhere can I get all this stuff?wikiHow ContributorCommunity AnswerAny home improvement store.Thanks!
QuestionCan this be made to be 20 feet long by four feet high?wikiHow ContributorCommunity AnswerOf course, but 20x4 wood would be a bit hard to find at a store.Thanks!
QuestionHow do I bend good one-side plywood that's a half inch thick?wikiHow ContributorCommunity AnswerYou can wet it (soak it in water because doing so makes the wood more flexible) and then apply glue on the edge of the wood that is going to be the side of the ramp. Then gradually nail or screw it on, making sure to clamp it down or press it in place with a weight so that it takes the form that you want it to have. Be careful, though, as you may break it if you don't proceed patiently or if you wet it too little.Thanks!
What about if it was a mini half pipe?
What do you need to build it
How do you build the landing pad
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
- Caution, if you build a 10' ramp with 5' of vertical, it will be like skating the shallow end of a pool...fun, but not practical...on a 10' tall ramp, I would suggest a 9' radius and 1' of vertical.
- You can shim under the framing if the ground is uneven, just make sure it's solid.
- The short lengths of the 2x4s is to curb deflection. You can use longer lengths if you can figure out a way to brace them.
- Make sure the half-pipe is sturdy. If not try using concrete or burying about 6 inches (15.2 cm) of the quarter pipes in the ground.
- If you like you can cover the base of the half pipe with Plexi Glass to enhance your skating experience.
- Don't build a pipe with vertical, your beginner pipe should be 3–5 feet (0.9–1.5 m) high on a 8 foot (2.4 m) radius. Vertical is for pro skaters and most pro skaters know how to build ramps.
- This is just a suggestion on how to build a half-pipe, no guarantee on if it will work.
- Consult a pro about anchoring and framing properly to support the loads.
- Ask a professional builder for help or order plans from the internet from a professional ramp company.
Video: How to build a halfpipe from start to finish
How to Start a Story
How to Treat Neuropathy in Feet
How to Still Have Hot Sex When You’re Staying at Your Parents’ House
Don’t Laugh, But Hula-Hooping Is My New (and Only) Favorite Way toExercise
How to Make Nutella Swirled Pumpkin Bread
How To Pack A Suitcase Like A Pro
Nike: Biggest sneaker advantage becoming a huge liability
Glazed Irish Corn Beef Recipe
How to Clean Alloy Wheels
How to Write a Sports Article
Talk Therapy to Tackle Fear of the Dentist
Who Me Irrelevant An Essay On Aging
Date: 06.12.2018, 18:23 / Views: 73444