Master-class jewelry box with lily
The basis of the container, and the flower is made of shiny plastic suede.In work we will use: - small plastic container with curled cover. - paper adhesive tape. - scissors. - pink fabric for the box. - a little shiny film. - red braid. - Moment glue.- iron. - shiny plastic suede red and green. - plastic sheet imprint. - toothpick. - ear stick. - stamens for flowers. - glue gun. First, let's start with making a flower. We make templates. From a circle with a diameter of 7 cm we draw three petals with a common middle in the center. We also need separate petals with a height of 5.5 cm. In addition, we outline leaves with sharp corners.And let's start cutting out the details on templates from suede.Three triple red petal circles, individual 5 petals and 4 green leaves.And green pruning will still be needed to decorate the bud.And on this casket with a large flower is ready.
Suede under the influence of heat changes its shape, and therefore we will use the iron. Let's start with the individual petals. Apply to the hot plane with the seamy side without glitter. As soon as the workpiece from the heat began to shrink, we remove and use a new shape with our clubs. Press the bottom edge of the petal with your thumb, and on the inside of the other hand, bend the part in half and slide your fingers up to the edge of the petal, slightly stretching it.On the green remnants we will also make small bends.Now we turn to making a bud. On the cotton shelf cut off the edge on one side. This end of the stick is pierced from the wrong side in the center of the red petal circle. And we stretch cotton to the beginning.Clay" Moment "lubricate cotton wool and petals on the inside.We press the bottom and the top, and then we glue the sides and we get a closed box.Only then on the free edge of the wand we attach green thin details . With this we close the stem itself and decorate the bud.Next we proceed to assembling a flower. First we take the finished stamens, bend them in half and fasten the edge.Then in the center of the second petal circle make a small hole and insert into it bunch of stamens. We fix all the details of the flower on the glue gun.Next we stick the petals with stamens in the middle of three more petals. We try to arrange the petals in staggered order with respect to the first row.Now we still have 5 more separate petals,which fasten in a circle from the wrong side of the flower.Get a flower with volumetric petals.And for its decoration between large petals we will glue 4 green leaflets. One segment will be free for the bud.The flower is completely ready.The stage to decorate the very basis of the box has arrived. Take a small container, the lid diameter of which is 9 cm. And the lid itself is twisted.For preliminary pasting we use paper adhesive tape. We leave a place with a thread on the lid, and do not touch the inner sides and the thread on the jar.From the shiny foil cut two circles ,which will be inside at the bottom of the jar and lid.They will be well fixed thanks to the base of adhesive tape.And on the outer sides of the container we glue pink fabric. We cut a strip by the size of this jar, and we make it 1 cm larger than the existing size. We cut this excess a little with scissors and press it to the bottom of the casket.Cut an extra circle to close the free part of the bottom.The cover is also treated with a cloth on top. But in addition, you need to glue the red braid, placing it on the very edge of the lid.Now that the cover is ready, we will decorate it. We try the flower and mark the location of the middle of the lily. Then we glue the bud with the edge of the stem to the intended place.It remains to secure the lily itself, given the free space for the bud. And if the petals and leaves hang heavily from the roof, they should be slightly raised closer to the flower and glued. So that when opening the lid they do not interfere with the fingers.On the jar you can attach any small decorations at your discretion.
We make the same shape on three petal circles. The middle remains untouched.Moving on to the green leaves, there are 4 blanks. It is necessary to make streaks. You can draw a toothpick gently on the front side.It will also be beautiful after processing on the impression of a sheet of plastic. In this case, we place the workpiece from the suede face down on the plastic, and from above we put a white sheet of paper. Iron iron on the details through the paper. Imprint is interesting.Next, one should add small incisions with scissors along the edge. And we apply a sheet to the iron while standing sideways, and then with our fingers we make additional bends.
Booties socks. Knitting
50 Ideas of old chairs
For lovers of herring - a real find: insanely tasty and original
How to adjust the valves in the engine of the car VAZ-2109
Workshop New Year Tree
How to add admin css